Rolling friction coefficient level assessment quantifies the rolling resistance of tires, wheels, bearings, and polymeric materials under controlled laboratory conditions, providing essential data for energy-efficiency optimization and regulatory compliance. Testing performed by accredited third-party laboratories in accordance with ISO, ASTM, EN, GB, and JIS standards supports product development, tire energy labeling, and quality control across the automotive, railway, bearing, and material handling industries. This article explains the technical fundamentals, sample requirements, measured parameters, testing methods, and typical applications of rolling friction coefficient evaluation.
Technical Overview
Rolling friction, also referred to as rolling resistance, is the force or moment that opposes the rolling motion of a body (such as a wheel, tire, ball, or roller) over a surface under an applied normal load. Unlike sliding friction, rolling friction arises primarily from micro-deformation and viscoelastic hysteresis in the contacting materials, together with minor contributions from surface roughness, adhesion, and aerodynamic or lubrication effects. The rolling friction coefficient is commonly expressed as the dimensionless rolling resistance coefficient (Crr), defined as the ratio of the rolling resistance force to the normal load, or equivalently as the ratio of the rolling resistance moment to the product of normal load and rolling radius.
Representative ranges of the rolling friction coefficient include approximately 0.001–0.002 for a steel railway wheel on a steel rail, 0.001–0.0015 for precision ball bearings, 0.004–0.008 for bicycle tires on asphalt, and 0.010–0.015 for passenger car tires on concrete. Because rolling resistance can account for roughly 15–30% of the energy consumption of road vehicles in mixed driving conditions, and a substantially larger share for electric vehicles at steady speeds, even modest reductions in the rolling friction coefficient translate into measurable fuel savings or extended driving range. For this reason, rolling friction coefficient level assessment has become a core element of tire development, energy-efficiency labeling schemes, bearing selection, conveyor and caster design, and material qualification programs.
The key factors that influence measured rolling friction levels include material viscoelastic properties, normal load, rolling speed, ambient and surface temperature, surface roughness and geometry of the counter-surface, tire inflation pressure, and the mechanical condition of the test equipment. Reliable assessment therefore requires strictly controlled test conditions, standardized conditioning procedures, and, in many cases, thermal and speed corrections defined by the applicable standard.
Testing Samples
Pneumatic Tires
Passenger car tires (class C1), light truck tires (C2), and truck and bus tires (C3) constitute the largest category of rolling friction assessment samples. Tires are typically tested in an unmounted, cured condition after being mounted on a designated rim, inflated to the reference pressure, and conditioned at laboratory temperature in accordance with ISO 291 or the conditioning requirements of ISO 28580.
Wheels, Casters, and Rollers
Industrial casters, conveyor rollers, solid wheels, railway wheelsets, and wheelchair or logistics trolley wheels are evaluated to compare rolling efficiency across wheel materials (rubber, polyurethane, polyamide, phenolic, cast iron) and floor surfaces. These samples are usually tested as complete wheel assemblies on representative track or drum surfaces.
Bearings and Rolling Elements
Ball bearings, cylindrical roller bearings, tapered roller bearings, and individual rolling elements (balls, needles, rollers) are assessed to characterize running torque and frictional losses, which directly affect mechanical efficiency, heat generation, and energy consumption in rotating machinery.
Polymeric and Elastomeric Materials
Rubber compounds, thermoplastic polyurethanes, engineering plastics, and packaging materials are evaluated in coupon, ball, or wheel form to rank material formulations for rolling applications such as rollers, guide wheels, transport systems, and consumer products.
Testing Items
A rolling friction coefficient level assessment program typically reports the following measured and derived quantities:
- Rolling resistance force, in newtons (N), measured at the specified reference speed and load.
- Dimensionless rolling friction coefficient (Crr = Frr / N), where Frr is the rolling resistance force and N is the normal load.
- Rolling resistance moment, in newton-meters (N·m), particularly for bearing and wheelset evaluations.
- Normalized rolling resistance coefficient in N/kN, as used in tire energy labeling regulations based on ISO 28580.
- Single-point rolling resistance coefficient at the ISO 28580 reference condition (nominally 80 km/h with the standard load and inflation pressure defined for the tire class).
- Multi-point rolling resistance curves as a function of speed, load, and inflation pressure, in accordance with ISO 18164.
- Temperature-corrected results referenced to 25 °C, using the correction algorithms specified in the test standard.
- Repeatability and reproducibility statistics from replicate measurements, reported in line with ASTM G115 guidance on measuring and reporting friction coefficients.
Testing Methods
Drum Method (ISO 28580 / GB/T 18861)
The drum method is the internationally recognized reference procedure for tire rolling resistance. The test tire is loaded against a large rotating steel drum (typically 2.0 m in diameter), and the rolling resistance force is derived from the measured drum reaction force, spindle force, or torque input. Testing is performed at the single reference point of ISO 28580 (nominal speed 80 km/h with the prescribed load and inflation pressure) or across multiple speeds and loads per ISO 28580 Annex and ISO 18164. Results are corrected for drum surface curvature and drum temperature and are aligned to the international master drum network to ensure global comparability. The Chinese national standard GB/T 18861 corresponds to this drum-based approach for domestic regulatory use.
Drum Method with Force and Torque Transducers
For bearings and small wheels, a calibrated drum or driven shaft configuration with high-resolution force or torque transducers measures the frictional moment directly. This approach is widely applied to rolling element bearings, where the friction coefficient is extracted from measured torque under specified radial or axial load, speed, and lubrication conditions, following ISO and JIS bearing test practices.
Inclined Plane Method
In the inclined plane method, a ball, wheel, or roller is placed on a flat specimen surface whose tilt angle is slowly increased until the onset of rolling occurs. The rolling friction coefficient is calculated from the critical angle and the rolling element radius. This simple and low-cost method is well suited to material comparison studies, quality screening, and small components, provided that surface flatness and vibration are carefully controlled.
Traction (Towing) Method
In the traction method, the specimen wheel or assembly is towed at constant speed along a flat track, belt, or plate while a load cell measures the horizontal tractive force. Dividing the measured force by the vertical load yields the rolling friction coefficient. This method is commonly used for casters, solid wheels, conveyor rollers, and floor-wheel system evaluations, and it permits testing against customer-specified floor materials.
Coast-Down (Deceleration) Method
In the coast-down method, the rolling body or test assembly is accelerated to a reference speed and then allowed to decelerate freely while its velocity decay is recorded. The deceleration profile, corrected for aerodynamic drag and drivetrain losses, is used to compute the rolling resistance force and coefficient as a function of speed. This method is useful for full-vehicle verification and for wheels operating on long flat tracks.
Environmental and Parametric Conditioning
All methods incorporate standardized conditioning, typically at least 24 hours at 23 ± 2 °C and 50 ± 5% relative humidity in accordance with ISO 291, together with warm-up rolling prior to data acquisition. Controlled-temperature chambers allow assessment from sub-zero conditions to elevated temperatures (for example, −10 °C to 60 °C), enabling evaluation of temperature sensitivity and thermal correction coefficients.
Applications
Rolling friction coefficient level assessment delivers direct value across numerous industries and regulatory contexts:
- Tire development and energy labeling: rolling resistance classes on regional tire labeling schemes are based on ISO 28580 results, driving low-rolling-resistance compound design and market compliance.
- Automotive and electric vehicle engineering: friction data feed vehicle energy consumption models, range estimation, and warranty verification for original equipment tire approvals.
- Railway engineering: wheel-rail rolling resistance assessments support traction energy calculations, lifecycle cost analysis, and braking system design.
- Bearing and machinery manufacturing: friction coefficient verification confirms efficiency ratings, lubrication performance, and torque specifications for rotating equipment.
- Material handling and logistics: caster and conveyor roller evaluations optimize warehouse equipment selection, reduce manual handling forces, and support ergonomic compliance.
- Polymer and rubber research: comparative rolling friction data guide formulation development for tread compounds, polyurethane wheels, and engineered rollers.
- Quality control and supplier qualification: periodic rolling friction testing verifies lot-to-lot consistency and incoming material conformity against agreed specification limits.
FAQ
What is the difference between rolling friction and sliding friction?
Sliding friction resists relative surface motion when one body slides across another, whereas rolling friction resists rolling motion and originates mainly from deformation hysteresis in the contact zone rather than surface shearing. Rolling friction coefficients (typically 0.001–0.015) are generally one to two orders of magnitude lower than sliding friction coefficients, which is why wheels and bearings are so effective at reducing energy losses.
Is the rolling friction coefficient a dimensionless quantity?
In modern practice, the rolling resistance coefficient is dimensionless because it is defined as the rolling resistance force divided by the normal load, or equivalently in N/kN units for tire labeling. In classical mechanics, the coefficient of rolling friction is sometimes expressed as a small length (the offset of the resultant reaction force), which becomes dimensionless when divided by the rolling radius. Test reports should always state the definition used.
Which standards govern rolling friction coefficient assessment?
The principal standards are ISO 28580 (single-point tire rolling resistance for passenger car, truck, and bus tires), ISO 18164 (multi-point tire rolling resistance measurement), GB/T 18861 (the corresponding Chinese national tire standard), ISO 291 (specimen conditioning), and ASTM G115 (reporting of friction measurement results). Regional tire labeling regulations reference ISO 28580 as the technical basis for energy classes. Additional JIS and EN standards apply to specific product sectors such as rolling stock and industrial wheels.
What sample quantities and preparation are required?
For tire drum testing, typically at least three tires of the same size and pattern are recommended to establish statistical confidence. For material and component testing, five or more replicate specimens are customary. All samples should be fully cured or finished, clean, free of defects, and conditioned for a minimum of 24 hours at 23 ± 2 °C and 50 ± 5% relative humidity before measurement.
How accurate and reproducible are the results?
ISO 28580 defines a correlation and alignment procedure that links laboratory drums to a common reference, yielding tight inter-laboratory reproducibility suitable for regulatory labeling. For other methods, measurement uncertainty depends on force transducer accuracy, speed and temperature stability, and surface preparation; typical repeatability within a single laboratory is a few percent of the measured coefficient. Reports from accredited third-party laboratories include measurement uncertainty statements and full traceability of calibration.
Can rolling friction be tested at different temperatures and speeds?
Yes. Environmental chambers and variable-speed drives allow assessment from sub-zero to elevated temperatures and across the full operating speed range of the product. Multi-point testing per ISO 18164 characterizes how the rolling friction coefficient varies with speed, load, and inflation pressure, and provides the thermal correction coefficients required for standardized reporting.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing