Ubicación: Global + English
Global Global Algérie Français Algeria English Angola Português Angola English Argentina Español Argentina English Australia English Austria Deutsch Austria English Azerbaijan English Azerbaijan Русский Bahrain English Bangladesh English Belgium English Belgium Français Belgium Nederlands Brazil Português Brazil English Bulgaria български Bulgaria English Cameroon English Cameroon Français Canada English Canada Français Chile Español Chile English China 中文 China 日本語 China English Colombia Español Colombia English Croatia English Czech Republic Čeština Czech Republic English Denmark English Djibouti English Ecuador Español Ecuador English Egypt English Estonia English Ethiopia English Finland Suomi Finland English France Français France English Georgia English Georgia Русский Germany Deutsch Germany English Ghana English Greece Ελληνικά Greece English Guatemala Español Guatemala English Hong Kong, China English Hong Kong, China 中文 Hungary Magyar Hungary English India English Indonesia English Iraq English Ireland English Italy Italiano Italy English Ivory Coast Français Ivory Coast English Japan 日本語 Japan English Jordan English Kazakhstan Русский Kazakhstan English Kenya English Kuwait English Kyrgyzstan Русский Kyrgyzstan English Latvia English Lithuania English Malaysia English Mauritius English Mauritius français (Maurice) Mexico Español Mexico English Moldova Română Moldova English Mongolia English Morocco English Morocco Français Mozambique Português Mozambique English Netherlands Nederlands Netherlands English New Zealand English Nigeria English Norway English Oman English Pakistan English Paraguay Español Paraguay English Peru Español Peru English Philippines English Poland Polski Poland English Portugal Português Portugal English Qatar English Republic of Korea 한국어 Republic of Korea English Romania Română Romania English Saudi Arabia English Serbia Српски Serbia English Singapore English Slovakia English Slovenia English South Africa English Spain English Spain Español Sri Lanka English Sweden English Switzerland Deutsch Switzerland Français Switzerland Italiano Switzerland English Tanzania English Thailand ไทย Thailand English Togo English Togo Français Tunisia English Tunisia Français Türkiye Türkçe Türkiye English Turkmenistan Русский Turkmenistan English Ukraine Українська Ukraine English United Arab Emirates English United Kingdom English Uruguay Español Uruguay English USA English Uzbekistan English Uzbekistan Русский Vietnam Tiếng Việt Vietnam English

PET Film Coefficient of Thermal Expansion (CTE) Testing and Determination

The coefficient of thermal expansion (CTE) is one of the most critical performance parameters for PET film, governing dimensional stability in flexible electronics, displays, photovoltaic modules, and precision packaging applications. This article provides a comprehensive technical overview of PET film CTE measurement, covering sample requirements, testing items, internationally recognized methods such as ASTM E831 and ISO 11359-2, typical result ranges, and practical guidance for engineers and quality professionals. Accredited third-party laboratories routinely perform these determinations to support material qualification, incoming inspection, and failure analysis.

Technical Overview

Polyethylene terephthalate (PET) film is a biaxially oriented, semi-crystalline polyester film widely used as a dielectric substrate, protective layer, and structural component in electronic and industrial products. Because most PET film is produced by sequential or simultaneous biaxial stretching, its thermal expansion behavior is anisotropic, differing between the machine direction (MD) and transverse direction (TD). The coefficient of thermal expansion (CTE) quantifies how much the film dimension changes per unit temperature change and is typically expressed in ppm/°C (equivalent to 10⁻⁶/K or µm/(m·°C)).

The linear CTE is defined as the fractional change in length per degree of temperature change at constant pressure: α = (1/L₀) × (dL/dT). In practice, a mean CTE over a specified temperature interval is reported: ᾱ = ΔL / (L₀ × ΔT). For PET, the CTE is strongly dependent on temperature relative to the glass transition. Below the glass transition temperature (Tg, approximately 75–80°C for PET), standard biaxially oriented PET film typically exhibits a CTE of roughly 15–30 ppm/°C, while heat-stabilized or low-expansion specialty grades can achieve values of 15 ppm/°C or lower. Above Tg, the amorphous phase softens and the apparent expansion coefficient rises sharply, often exceeding 100 ppm/°C.

Accurate CTE determination matters because thermal expansion mismatch between PET film and adjacent materials such as copper, silicon, glass, or adhesives causes warpage, curling, delamination, and misregistration during thermal processing and service. Designers of flexible printed circuits, display modules, and optical film stacks therefore specify CTE limits in both MD and TD as part of material qualification.

It is important to distinguish CTE from thermal shrinkage. CTE describes reversible dimensional change during heating and cooling, whereas shrinkage reflects irreversible relaxation of oriented molecular chains and crystallization at elevated temperature, typically measured after a defined heat exposure. Both properties are frequently evaluated together in a complete thermal stability characterization of PET film.

Testing Samples

Standard Biaxially Oriented PET (BOPET) Films

Commercial BOPET grades ranging from approximately 12 µm to 250 µm in thickness are the most commonly submitted samples. These include general-purpose films for packaging, laminating, and insulation, as well as electrical-grade and capacitor-grade films. Specimens must be cut in both MD and TD because of the pronounced anisotropy introduced by the orientation process.

Heat-Stabilized and Low-CTE Specialty Films

Specialty PET films that have undergone in-line or off-line heat stabilization are used in flexible printed circuits, flexible displays, and precision graphic applications where low CTE and low shrinkage are required. These grades typically show MD/TD CTE values below about 15 ppm/°C in the sub-Tg region and significantly reduced residual shrinkage. Testing of these films verifies whether supplier specifications are met.

Coated, Metallized, and Composite PET Films

PET films carrying functional coatings such as hard coats, anti-static layers, barrier coatings (for example, silicon or aluminum oxide), or vacuum-deposited metal layers can also be characterized. In laminated or composite structures, the measured CTE represents the effective value of the multilayer stack, which is useful for predicting the behavior of the assembled component.

Specimen Geometry, Cutting, and Conditioning

For thermomechanical analysis in tension mode, specimens are typically cut as rectangular strips approximately 5–10 mm wide with an effective length of 10–20 mm, depending on the instrument fixture. Edges must be straight and free of nicks, burrs, and wrinkles, since stress concentrations cause premature tearing or slip at the clamps. Specimens are conditioned prior to testing at 23 ± 2°C and 50 ± 5% relative humidity in accordance with ISO 291 or ASTM D618, generally for a minimum of 24 hours, because moisture content measurably influences the thermal response of PET. When evaluating dry-state behavior, specimens may additionally be pre-dried in a desiccator or low-temperature oven and tested immediately.

Testing Items

A complete CTE characterization of PET film typically includes the following test items:

  • Linear CTE below the glass transition (for example, over the interval 25–70°C), reported separately for MD and TD.
  • Apparent CTE above the glass transition region, which characterizes the softened state and is relevant for high-temperature processing windows.
  • Mean CTE over client-specified engineering temperature ranges, such as −40 to 85°C for automotive electronics or 23 to 60°C for consumer devices.
  • CTE anisotropy ratio between MD and TD, an indicator of balance in the biaxial stretching process.
  • Glass transition temperature determined from the inflection in the dimension-versus-temperature curve, in accordance with ISO 11359-2.
  • Complementary thermal shrinkage after defined heat exposure, such as 150°C for 30 minutes or 190°C for 30 minutes, frequently requested together with CTE for flexible circuit substrates.

Testing Methods

Thermomechanical Analysis (TMA) — Primary Method

Thermomechanical analysis is the industry-standard technique for CTE determination of thin polymer films. The specimen is clamped in a film or fiber tension fixture, a small static force (typically in the range of 0.01–0.1 N) is applied to keep the specimen taut without plastically deforming it, and the sample is heated at a controlled rate, usually 3–5°C/min, under a nitrogen purge. The probe displacement is recorded continuously as a function of temperature, and the CTE is obtained from the slope of the length-change curve over the specified temperature interval.

The governing standards are ASTM E831 (Standard Test Method for Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis) and ISO 11359-2 (Plastics — Thermomechanical analysis — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature). The Chinese national standard GB/T 1036 provides a comparable procedure for the determination of the linear thermal expansion coefficient of plastics. Because PET carries processing-induced thermal history, laboratories commonly perform a first heating run to erase free-volume and orientation-related artifacts, followed by a second heating run from which the reported CTE is calculated, in agreement with the client on which heating run represents the intended use condition.

Quartz Dilatometry — ASTM D696

For CTE measurements close to room temperature, vitreous silica dilatometry per ASTM D696 over the range of approximately −30°C to 30°C remains a valid alternative, particularly for thicker specimens. The low intrinsic expansion of the quartz dilatometer allows accurate measurement of the small dimensional changes of PET, although the technique is less common for thin films where clamping and specimen straightness present practical difficulties.

Non-Contact Optical and Dimensional Stability Methods

For flexible circuit and display applications, optical dimensional measurement methods described in IPC-TM-650 (for example, method 2.2.4 for dimensional stability of flexible dielectric materials) are used to quantify irreversible size change after thermal exposure. Photolithographically etched or optically tracked benchmark patterns are measured before and after conditioning at specified temperatures. While these methods do not yield a true CTE, they provide essential complementary data on the total dimensional change a manufacturer can expect in production.

Data Reduction, Calculation, and Reporting

The mean linear CTE is calculated as ᾱ = (L₂ − L₁) / (L₀ × (T₂ − T₁)), where L₀ is the original gauge length and L₁, L₂ are the specimen lengths at temperatures T₁ and T₂. Best practice uses linear regression over the selected temperature window rather than two discrete points to reduce scatter. The test report should state the specimen direction (MD or TD), thickness, temperature interval, heating rate, applied force, conditioning history, heating run number, and the individual and mean results of at least three replicate specimens. Typical measurement repeatability for well-prepared PET film specimens is within 1–3 ppm/°C.

Applications

CTE data for PET film directly support engineering decisions across many industries:

  • Flexible printed circuits and adhesiveless flexible copper-clad laminates, where CTE mismatch with copper foil drives curl, pad misalignment, and via cracking.
  • Flexible display substrates and cover films, where dimensional stability at elevated processing temperatures is essential for layer-to-layer registration.
  • Optical film stacks for LCD and OLED modules, including protective, diffusing, and reflective films, where thermal expansion causes visible wrinkling and mura defects.
  • Photovoltaic backsheets, where PET inner and outer layers must accommodate thermal cycling alongside cell and encapsulant materials.
  • Membrane switches, flexible sensors, and printed electronics, where conductor traces printed on PET must maintain registration through thermal excursions.
  • Metallized film capacitors, where dimensional change of the polymer film affects winding tightness and capacitance stability.
  • Precision graphic arts, hot stamping foils, and thermal transfer ribbons, where registration accuracy depends on low and predictable expansion.
  • Material selection, incoming inspection, supplier benchmarking, and root-cause investigation of warpage or delamination failures.

FAQ

What is a typical CTE value for PET film?

Standard biaxially oriented PET film generally shows a CTE of approximately 15–30 ppm/°C below its glass transition temperature, with MD and TD differing due to the stretching balance. Heat-stabilized low-expansion grades for electronics applications are commonly specified at 15 ppm/°C or below, and premium grades can approach the CTE of some metals. Above Tg, the apparent CTE increases dramatically and is normally reported separately.

Why must MD and TD specimens be tested separately?

Biaxial stretching aligns polymer chains preferentially along the stretch directions, producing anisotropic thermal expansion. The machine direction and transverse direction can differ by several ppm/°C, and laminate or circuit design depends on knowing both values. Reporting a single average would mask this anisotropy and lead to incorrect warpage predictions.

What temperature range should the CTE be measured over?

The interval should bracket the actual service or processing temperatures of the end product and remain below the glass transition unless elevated-temperature behavior is specifically required. Common windows include 25–70°C for general sub-Tg characterization and −40 to 85°C for automotive-grade qualification. Spanning Tg within a single reported interval is discouraged because the slope changes discontinuously and the resulting mean value has little physical meaning.

How does CTE differ from thermal shrinkage?

CTE describes the largely reversible dimensional change during heating, derived from the slope of the expansion curve. Thermal shrinkage is an irreversible contraction caused by relaxation of oriented molecules and further crystallization, measured after holding the film at a specified temperature. A heat-stabilized film may have similar sub-Tg CTE to a standard grade but far lower shrinkage, so the two parameters answer different engineering questions.

How much sample is required for a TMA CTE test?

Each measurement normally requires a strip roughly 5–10 mm wide and 10–20 mm long in the test direction. Since both MD and TD are measured with a minimum of three replicates per direction, a practical submission is a flat, wrinkle-free sheet of at least 100 mm × 100 mm, ideally supplied on its original core or carrier to preserve flatness.

Which factors most strongly influence the accuracy of PET film CTE results?

The dominant factors are specimen edge quality, applied static force, heating rate, moisture conditioning, and the heating run selected for data reduction. Excessive force plastically draws the film; insufficient force allows slack and apparent negative expansion; and residual thermal history from manufacturing shifts the first-heating curve. Consistent control of these parameters, together with replicate testing, delivers the repeatability needed for specification acceptance.

Can CTE be measured through the thickness of the film?

Thin PET films are usually too thin for reliable through-thickness dilatometric measurement in compression mode. Thickness-direction expansion is occasionally estimated from volumetric expansion relationships or measured on stacked laminates, but for practical qualification purposes the in-plane MD and TD values are the accepted acceptance criteria.

Which standards govern PET film CTE testing?

The principal methods are ASTM E831 and ISO 11359-2 for thermomechanical analysis, ASTM D696 for quartz dilatometry, GB/T 1036 as the corresponding Chinese national method for plastics, and IPC-TM-650 procedures for complementary dimensional stability evaluation of flexible circuit materials. Accredited third-party laboratories can perform testing under these frameworks and issue reports suitable for supplier qualification and regulatory submissions.

Why Choose ZKGX?

  • State-of-the-art analytical equipment
  • Highly qualified scientific team
  • Fast turnaround time
  • Competitive pricing